Forklift Operation Safety: Load Centers, Ramps, Tip-Overs, and Refueling

November 1, 2026 · SafePath OSHA Team Forklift SafetyVehicles & EquipmentOSHA 30

A forklift looks simple until you drive one. It can weigh up to three times as much as a car, it steers with its rear wheels, and its narrow wheelbase makes it naturally unstable. Thousands of workers are seriously injured in forklift accidents every year, and more than 100 are killed. Those victims include both operators and pedestrians.

OSHA calls these machines powered industrial trucks. In construction, 29 CFR 1926.602(d) requires operator training that matches the general industry requirements at 29 CFR 1910.178(l). Here’s what that training needs to stick in your head.

Why forklifts tip

A forklift works like a seesaw, with the front wheels as the pivot point. The load sits on one side and the counterweight on the other. Adding a load shifts the truck’s center of gravity forward.

To picture what’s safe, imagine lines connecting the two front wheels and the pivot point of the rear axle. That’s the stability triangle, and the center of gravity has to stay inside it. Four things push it toward the edge:

  • Heavy loads move it forward, toward the front wheels.
  • Off-center loads pull it to one side.
  • Raised forks or loads make the truck less stable the higher they go.
  • Turns shift it toward the outside of the turn.

As the center of gravity moves forward, the rear wheels also lose traction. They do the steering, so a skid can cost you control of the truck.

Know your load center

Every forklift has a rated load capacity, and that rating depends on the load center: the distance from the backrest to the load’s center of gravity. Most forklifts are rated at a 24-inch load center, which is half the depth of a standard pallet.

Here’s where operators get caught. A forklift rated for 4,000 lb at 24 inches can’t safely lift a 4,000 lb load with a 36-inch load center. The extra distance shifts the center of gravity forward and can tip the truck.

When you pick up a load:

  1. Square up to the pallet and drive forward slowly until the load touches the backrest.
  2. Check that the forks reach at least two-thirds of the load’s length.
  3. Set the forks wide enough to support the load evenly, and center it side to side whenever possible.
  4. Raise it only as far as you need to, using only enough backward tilt to stabilize it.
  5. Lower the forks to 4 to 6 inches off the ground before moving.

Have badly stacked loads or damaged pallets restacked on a new pallet before you lift them. If a load is still too far forward, rearrange the materials to get the correct load center.

Rules for driving and turning

Before you climb on, ask whether you’re fit to drive. A sore back, an argument with a coworker, or cold medicine can all affect your focus. Never operate a forklift under the influence of drugs or alcohol.

Once you’re in the seat, buckle up before you turn the key, then follow these basics:

  • Speed: No faster than a normal walking pace.
  • Direction: Keep to the right and face the way you’re traveling. If the load blocks your view, drive in reverse with the load trailing.
  • Turns: Brake gradually, stop completely before changing direction, and steer in a slow, smooth sweep.
  • Following distance: Stay at least three truck lengths behind other forklifts, and don’t pass them.
  • Surfaces: Watch for grease, water, sand, gravel, and trash. Keep your wheels away from the edges of ramps, platforms, and loading docks.
  • Clearance: Check overhead for lights, pipes, sprinklers, and low doorways. Keep the mast and forks at least 10 feet from electrical wires or equipment.

Ramps and grades

The rule changes depending on whether you’re carrying a load:

Forklift conditionForks pointGoing upGoing down
LoadedUphillDrive forwardDrive in reverse
UnloadedDownhillDrive in reverseDrive forward

Driving a loaded truck forward down a grade can slide the load right off the forks. If your load blocks your view on the way up, have a coworker spot for you. Either way, go slowly and travel straight. Turning on an incline or driving across one can tip the truck sideways.

If the forklift tips

Remember: Do not jump. Stay in the seat with your belt on, brace your feet, grip the steering wheel, pull yourself tight against it, and lean away from the direction of the tip.

Jumping feels like the natural reaction, but it can leave you in the path of the falling truck.

Protecting people around the truck

Pedestrians always have the right of way, and they may not understand what a forklift can do. Forklifts and the materials they carry are also a struck-by hazard, so keep these rules on every shift:

  • Sound the horn at cross aisles, turns, intersections, and doorways.
  • Make eye contact to confirm that people have noticed you.
  • Never drive toward someone standing in front of a wall, bench, or other fixed object.
  • Don’t let anyone walk under raised forks, loaded or not.
  • Never give anyone a ride on the forklift or on the load.

To raise a worker, use an aerial platform, also called a cage. Set it firmly against the backrest and secure it with a safety chain. Stay with the truck while the platform is raised, and never move the forklift with the platform elevated or with someone on it. Don’t let anyone stand on bare forks or a pallet, walk under the platform, or climb the mast.

Trucks, trailers, and dock plates

Before driving onto a truck or trailer, confirm that its brakes are set and its wheels are chocked. Check that the floor can support the combined weight of your forklift and load.

Use a dock plate to bridge the gap between the dock and a truck or rail car. Make sure it’s in good condition, secured in place, and rated for the forklift plus the load. Cross it slowly.

Inspect before every use

Start with a walkaround, looking for damage, missing parts, and leaks. Then work through this list:

AreaWhat to check
Engine trucksFuel, crankcase and transmission oil, coolant
Electric trucksBattery electrolyte level, terminal corrosion, loose connections
TiresDamage and stuck objects
ControlsSteering, service brakes, parking brake
Mast and forksChain, bearings, nuts, cotters, cracks, wear, alignment
HydraulicsReservoir oil level and signs of leaks
Safety devicesLights, horn, backup alarm, warning beacon, seat belt

Battery acid is corrosive, so put on PPE before you check electrolyte, including eye protection, a face shield, and rubber gloves. If something’s wrong, repair or report it and take the forklift out of service if necessary. Never use a faulty lift.

Refueling and recharging safely

Every power source carries a fire and explosion risk, including batteries, which can give off flammable hydrogen gas while charging. Shut off engines and motors before you begin. Refueling and charging areas need good ventilation, with no smoking, open flames, sparks, or other ignition sources.

Power typeKey safety steps
Compressed gas (propane)Close the tank valve and let the engine run until it stalls, which clears the fuel lines. Wear protective gloves because the gas can cause frostbite. Don’t use metal tools on the connections, and make sure the new tank engages the locking pin.
Gasoline or dieselTouch the nozzle to the fill pipe before fueling to discharge static electricity. Wipe up spills and let the residue evaporate before restarting.
ElectricKeep tools, jewelry, and watches away from the battery. On older trucks, leave the compartment lid open so the battery can cool and hydrogen can dissipate. Follow the manual for your model.

Parking the forklift

Whenever you leave a forklift unattended, lower the forks to the ground, set the parking brake, turn off the motor, and take the keys with you. If you have to park on an incline, chock the wheels.

How SafePath OSHA Fits Into This

Keeping forklift operators trained and crews clear of moving equipment is a daily job for supervisors, which is part of what the 30-hour card really means for a foreman.

SafePath OSHA 30 helps you train for your OSHA 30-Hour Construction card with 1,200 questions across all 24 topics, including 9 required topics and 15 electives. Its supervisor toolbox includes toolbox talks, incident reports, audit checklists, and crew certification tracking, so you can keep your safety talks and crew records in one place. It’s part of the SafePath OSHA suite, with 2200+ questions across 2 apps.

Remember: An OSHA Outreach card and a prep app don’t qualify anyone to operate a forklift. Operators need the training and evaluation required by OSHA, and their employer must certify them.

Frequently Asked Questions

What should you do if a forklift starts to tip over?

Stay in the seat and do not try to jump. Keep your seat belt on, brace your feet, grip the steering wheel, pull yourself tight against it, and lean away from the direction of the tip.

How high should forklift forks be when traveling?

Keep the forks 4 to 6 inches off the ground with the mast tilted back, whether or not you are carrying a load. Don't turn with the forks raised any higher than that.

Which way should you face when driving a forklift on a ramp?

With a load, keep the forks pointed uphill: drive forward going up and in reverse going down. Without a load, keep the forks pointed downhill: drive forward going down and in reverse going up. Travel straight and never turn on the grade.

Can you lift a coworker on forklift forks?

Never on bare forks or a pallet. Use an approved aerial platform secured to the forklift, stay with the truck while it's raised, and never move the forklift with the platform elevated or with someone on it.

How often does OSHA require forklift operators to be evaluated?

Operator performance must be evaluated at least once every three years under 29 CFR 1910.178(l), which applies to construction through 29 CFR 1926.602(d). Refresher training is also required after an accident, a near miss, or unsafe operation, among other triggers.

Ready to start practicing?

Free practice questions from every topic — in English and Spanish.

← Back to all articles